Canadian Electrical Industry News Week

 

July 9, 2017

Bill BurrIn this article: Section 52 — Diagnostic imaging installations. The CE code is a comprehensive document. Sometimes it can seem quite daunting to quickly find the information you need. This series of articles provides a guide to help users find their way through this critical document. This is not intended to replace the notes in Appendix B or the explanations of individual requirements contained in the CEC Handbook**, but will hopefully provide some help in navigating the code.

Rule 52-000 Scope states that Section 52 is a supplementary or amendatory section of the code and applies to the installation of X-ray and other diagnostic imaging equipment operating at any frequency, but does not provide any specifications for safeguards against radiation. Information on radiation safeguards is contained in the series of Health Canada Safety Codes for radiation protection. The CSA CEC Handbook provides additional explanations and tables.

Rule 52-002 provides some special terminology for this section, and defines momentary and long-term ratings of 20 seconds and 5 minutes respectively for operation of applied x-ray and computerized tomography equipment.

Rule 52-004 provides guidelines for guarding of high-voltage parts, and requires that high-voltage parts be contained within bonded to ground metal enclosures, or within separate rooms or enclosures where a circuit control switch controlling the diagnostic imaging equipment is interlocked, to be open when the door is open and unlocked, and be insulated from the enclosure. In addition, high-voltage circuit conductors must be of the shockproof type. If a milliammeter is provided, it must be either connected in the bonded-to-ground circuit conductor, or guarded, if connected in the high-voltage conductor.

Rule 52-006 permits mobile diagnostic equipment, and permanently connected diagnostic equipment on a 30 amp or less branch circuit, to be supplied with a plug and hard-usage cable or cord.

Rule 52-008 specifies that a disconnect must be placed in the supply circuit in a location accessible from the radiation control of the diagnostic equipment. The rating of the disconnect for X-ray or computerized tomography equipment is based on 100% of the power input required for the long-time rating of the equipment, or 50% of the power input required for the momentary rating of the equipment, whichever is greater. For equipment on a 120volt, 30amp circuit, the required disconnect may be a receptacle and plug of the appropriate size.

Rule 52-010 exempts transformers and capacitors, forming part of diagnostic imaging equipment, from the requirements of Section 26. This equipment must comply with the CEC Part II product standard for the equipment. Capacitors must be provided with a means for automatically discharging and grounding the plates when the supply is disconnected. This is not required if the current-carrying parts of the capacitors and conductors are located 2.5 meters or more above the floor and accessible to only authorized persons, or, if located within 2.5 meters of the floor, within

• metal enclosures that are bonded to ground, or
• enclosures of insulating material

Rule 52-012 provides for protection where step-up transformers are used for diagnostic equipment. The low-voltage circuit of the step-up transformer is required to have an overcurrent device with no exposed live parts, installed as part of or adjacent to the equipment that protects the high-voltage radiographic circuit from all fault conditions. Where the above overcurrent device is too large to protect other fluoroscopic or therapeutic circuits on the equipment, additional overcurrent protection needs to be installed to protect these circuits. In the case of portable equipment, the above requirements also apply. However, an exemption can be applied if all high-voltage parts are enclosed in a single metal enclosure, bonded to ground. Where more than one apparatus is supplied by a common high-voltage source, other switches must be installed to independently disconnect each apparatus from the high-voltage source.
Rule 52-014 reiterates that all non-current-carrying parts of apparatus, including ancillary equipment, must be bonded to ground in accordance with the requirements of Section 10.

Rule 52-016 provides the requirements for determining ampacity of supply conductors and rating of overcurrent protection for diagnostic imaging equipment. For a single piece of equipment, use the larger of

• the long-time current rating of the equipment, or
• 50% of the momentary current-rating required on a radiographic setting

Note that this information is contained on the equipment faceplate.

Where more than one piece of diagnostic equipment is supplied, the rating of the supply conductors and overcurrent device is based on

• the sum of the long time current ratings of all the equipment supplied by the circuit, or
• Tthe sum of 50% of the maximum momentary current rating for the two largest units supplied, plus 20% of the maximum momentary current rating of the other units, when the equipment is on a radiographic setting

In the next installment, we will be discussing Section 54 — Community antenna distribution and radio and television installations.

* The source for this series of articles is the Canadian Electrical Code, Part I, published by CSA
** Note the CEC Handbook is also published by CSA.

William (Bill) Burr is the former Chair of the Canadian Advisory Council on Electrical Safety (CACES), former Director of Electrical and Elevator Safety for the Province of BC, and former Director of Electrical and Gas Standards Development and former Director of Conformity Assessment at CSA Group. Bill can be reached at Burr and Associates Consulting billburr@gmail.com.

 The Evolution Series. Poke-Thru Devices, Floor, Wall and Ceiling Boxes 

Legrand Wiremold EvoFrom poke-thru devices to floor, wall and ceiling boxes, the Evolution Series has continued to increase device efficiency and reliability while providing durability and quality. Customizing your space and maximizing access to all the power, A/V and communications you could ever need. Evolution Series boxes bring power, communications and A/V to walls, floors and ceilings. Evolution adds flexibility, functionality and stylish good looks to every room you create when planning office buildings, airports, schools and hospitals.

 

 

Watch the video Here

 

Changing Scene

  • Prev
Global data cable, network and CCTV tester manufacturer IDEAL Networks has donated 26 testers to ...
Stanpro and Standard Products have officially completed their merger agreement announced in early ...
Prior to joining ABB in 2017 as Executive Vice President of the Electrification business, Deschenes ...
Susan Uthayakumar, country president, Schneider Electric, has been named a Women's Executive ...
ABB presented its electrification solutions that will allow customers to take full advantage of the ...
Electricity Human Resources Canada has introduced a new Board of Directors, effective as of their ...
Jacques Fiset, the new president of the EFC Quebec section, told us in a recent interview that his ...
Organised by the Hong Kong Trade Development Council (HKTDC), the twin lighting shows - the  ...
A Friday night, the end of summer, the weather is mild, and 2,500 people — customers, ...
Eaton focuses on developing personable connections in every aspect. In September, our team will be ...

AVNET and Rockwell AutomationRockwell Automation announced that it has signed an agreement to acquire privately held Avnet Data Security, LTD, an Israeli-based cybersecurity provider with over 20 years of experience providing cybersecurity services. Avnet offers a full set of IT/OT cyber services and solutions ranging from assessments, penetration testing, network & security solutions, and training to converged IT/OT managed services.

“Avnet’s combination of service delivery, training, research, and managed services will enable us to service a much larger set of customers globally while also continuing to accelerate our portfolio development in this rapidly developing market,” said Frank Kulaszewicz...

Read More

 

 

 

Latest Articles

  • Prev
Anyone working in the electricity sector in Canada knows the reality of how few women we have in ...
 Anyone working in the electrical industry knows the importance of labelling for both safety ...
IDEAWORKS engages undergraduate students and hires co-op students in Mohawk’s Energy and ...
Pick up a newspaper or scan your preferred electronic newsfeed and you’ll likely see a series ...
Britech Corp, one of Canada’s largest heating cable companies has signed a formal agreement ...
Electrical enclosures serve to protect electrical devices from adverse environmental influences, ...

Michelle BraniganWhile the time is always right to think about professional development and skills training, the new year marks a symbolic opportunity to make some career resolutions. Today’s evolving nature of work means that it’s likely workers will change jobs a few times over the course of their career, and emerging technologies in the workplace constantly require new skills and adaptability. With the federal government’s Canada Training Benefit (CTB) taking effect as of January 1, 2020, employers and workers across the country now have a flexible tool at their disposal when it comes to training and upskilling.

Read More

 

 

Tools for the Trade

  • Prev
  IDEAL Industries has introduced Combination Drill Taps to its tool lineup. Combining the ...
  Stripping and crimping device, 100 - 240 V input voltage, for insulated ferrules with a ...
Professional all-in-one cutter/stripper for coaxial and twisted pair cables     ...
  Klein Tools' Coax Explorrer 2 tests coaxial cable and maps up to 4 locations   ...
  Ideal Industries' T-14 wire stripper s are ideal for all professionals working within the ...
  The ATS850 conveyor eliminates all types of electro static discharge requirements. ...
  Lorik Tool & Automation has the experience and ability to manufacture a variety of ...
  Ideal Industries' 26 piece insulated Journeyman kit is ideal for new electricians or for ...
  Klein Tools Deluxe Fish Rod Set comes in 19 pieces that when assembled can fish wire and ...
  BendWorks Software was designed to help electrical contractors adopt this new process ...

Solar Irradiance MeterDesigned specifically to aid the installation of solar PV panels, Megger's new PVM210 solar irradiance meter features a compact design which, unlike most other irradiance meters, has the solar detector on the top of the instrument. This arrangement, combined with the useful measurement hold function, makes the PVM210 easy and convenient to use - even with just one hand - when working on a sloping roof or at the top of a ladder.

  • Small, light and easy to use
  • Designed for one-handed use
  • Safer for use on ladders
  • Available as a stand alone product, or in PV specialist kits

Read More

 

 

Juna AIMeet Juno AI, a portfolio of lighting devices that form the “backbone” of your smart and connected space.The Juno AI Speaker Light with Alexa Built-In is an advanced LED downlight that features a JBL® speaker and Amazon Alexa voice service in a single patent pending ceiling light fixture. It’s a 6” downlight, but much, much more.

Juno AI takes advantage of the most ideal location in the home – the ceiling – to create a smart ecosystem. It can control any smart home device that works with Alexa. No hub required. It not only illuminates a room, but also locks the doors, adjusts your thermostat, tells your family dinner is ready, runs the vacuum, reads you a book, dims the lights, plays music through

Read More

 

 

Peers & Profiles

  • Prev
Headquartered in Vancouver, Legend Power Systems is a global onsite energy management technology ...
LDS caught up with General Manager of EiKO’s Canadian division, Stephen Lee who was kind enough ...
“I had an awesome time, it was a lot of fun,” said Zach Agombar, who competed his way to 8th place ...
Held from November 7th to 9th in Orlando, Florida, and recently aired on ESPN 2, the Ideal National ...
Panel Upgrade Experts is an electrical contracting company started seven years ago by Paul ...
Chad Alexander is a Branch Manager with Contact Automation, which provides automation integration ...
Rob Milner is the Canadian National Science, Automation, Optical Gas Imaging & sUAS Manager for ...
EIN sat down with WiRE President & CEO Joanna Osawe to learn more about WiRE and the ...
For the second consecutive year, Paul Hannania was among the 162 professionals and apprentices to ...
Alexander Couckuyt, Director of Operations for Southwire Canada, spent the majority of his ...

 

Brett Castein and Jordan PrattBy Blake Marchand

Held from November 7th to 9th in Orlando, Florida, and recently aired on ESPN 2, the Ideal National Championships gives electricians a chance to display their skills in a high-level competition. The event expanded internationally for the first time this year — over 55,000 electricians from 5 countries attempted to qualify for a chance to compete in the championship event. Last year’s event was the first to feature electricians from outside the United States. For 2019 they increased the number of Canadian qualifiers, and extended the competition to Mexico, Australia and China.

Read More

 

 

Copper $US Dollar price per pound

Kerrwil Publications Great Place to Work. Certified December 2019 - December 2020

538 Elizabeth Street, Midland,Ontario, Canada L4R2A3 +1 705 527 7666
©2020 All rights reserved

Use of this Site constitutes acceptance of our Privacy Policy (effective 1.1.2016)
The material on this site may not be reproduced, distributed, transmitted, cached or otherwise used, except with the prior written permission of Kerrwil